Processing of Cu-Cr alloy for combined high strength and high conductivity


Metallic alloys
Mechanical Properties
Electrical Properties
Precipitation hardening


High strength and high conductivity (HSHC) are two intrinsic properties difficult to combine in metallic alloy design because; almost all strengthening mechanisms also lead to reduced conductivity. Precipitation hardening by nano-sized precipitates had proven to be the most adequate way to achieve the optimum combination of strength and conductivity in copper based alloys. However, established precipitation strengthened Cu- alloys are limited to very dilute concentration of solutes thereby limiting the volume proportion hardening precipitates. In this work, we report the investigation of the reprocessing of higher Cr concentration Cu- based alloys via rapid solidification. It is found that the rapid solidification in the as-cast ribbon imposed combined solution extension and ultra-refinement of Cr rich phases. X-ray diffraction evidences suggest that the solid solution extension was up to 6wt%Cr. Lattice parameters determined confirmed the many folds extension of solid solution of Cr in Cu. Thermal aging studies of the cast ribbons indicated that peak aging treatments occurred in about twenty minutes. Peak aged hardness ranged from about 200 to well over 300Hv. The maximum peak aged hardness of 380Hv was obtained for alloy containing 6wt.%Cr but with conductivity of about 50%IACS. The best combined strength/conductivity was obtained for 4wt.%Cr alloy with hardness of 350HV and conductivity of 80% IACS. The high strengths observed are attributed to the increased volume proportion of semi-coherent Cr rich nano-sized precipitates that evolved from the supersaturated solid solution of Cu-Cr that was achieved from the high cooling rates imposed by the ribbon casting process. The rapid overaging of the high Cr concentration Cu-Cr alloy is still a cause for concern in optimising the process for reaching peak HSHC properties. It is still important to investigate a microstructural design to slow or severely restrict the overaging process. The optimum HSHC property reported here is a rare combination of high strength (>350Hv ~ 900MPa) and conductivity (50 – 80% IACS) found in metallic alloys.


K. Han, R. P. Walsh, A. Ishmaku, V. Toplosky, L. Brando and J.D. Embury, High Strength and high electrical conductivity of bulk Cu, Phil. Mag. Vol. 84, No.34 (2004), 3705 – 3716.

P. Liu, J. Su, Q. Dong, and H. Li, Optimization of aging treatment in lead frame copper alloy by intelligent technique, Mater. Lett. Vol 59 (2005) 3337 – 3342.

Zhenyu Li, Jun Shen, Fuyang Cao, Qingchun Li, A high strength and high conductivity copper alloy prepared by spray forming, J. Mater. Proc Tech. 137 (2003) 60 – 64.

R. Markandeya, S. Nagarjuna and D.S. Sarma, Precipitation hardening of Cu–Ti–Cr alloys Mater Sci

& Engr A,371 (2004) 291 – 305.

M. M. Dadras and D. G. Morris, Examination of some high strength high conductivity copper alloys for high temperature applications, Script Met. Vol 38 (1998) 199 – 205.

N. Gao, E. Huttunen–Saarivirta, T. Tianen, and M. Hemmila, Influence of prior deformation on the age hardening of a phosphorus-containing Cu–0.61wt.%Cr alloy Mater Sci & Engr A,342 (2003) 270 – 278.

J. Su, Q. Dong, P. Liu, H. Li, B. Kang, Research on aging precipitation in a Cu–Cr– Zr–Mg alloy

Mater Sci & Engingr A,392 (2005) 422–426.

J. B. Correia, H. A. Davies, C. M. Cellars, Strengthening in rapidly solidified age hardened Cu-Cr and Cu-Cr-Zr alloys Act. Mater. Vol 45 (1997) 177–190.

J. B. Correia and H. A. Davies, Magnetic and structural monitoring of nanophase precipitation during ageing of water-atomised Cu–5% Co alloy powders, Act Mater. Vol 48, (2000) 4115–4123.

M. A. Morris and D. G. Morris, Microstructures and mechanical properties of rapidly solidified Cu-

Cr alloys, Act. Met. Vol 35, (1987) 2511–2522.

P Liu, BX Kang, XG Cao, JL Huang, HC Gu , Strengthening mechanisms in a rapidly solidified and aged Cu-Cr alloy Journal of materials science, 35, (2000) 1691 – 1694.

F. Lopez, J. Reyes, B. Campillo, G. Aguilar and J.A. Juarez-lslas, Rapid solidification of copper alloys with high strength and high conductivity, JMEPENG vol 6 (1997) 611-–614

J. Strobrawa, Z. Rdzawski, Dispersion strengthened nanocrystalline copper, Journal of Achievements in Materials and Manufacturing Engineering, Vol. 24 (2007) 35–41.

E. Botcharova, M. heilmaier, J. freudenberger, G. Drew, D. kudashow, U. Martin, L. Schultz, Supersaturated solid solution of niobium in copper by mechanical alloying J. Alloys & Compds, vol. 351 (2003) 119 – 125.

A. O. Olofinjana, and H. A. Davies, Mater. Sci. Engr. Vol A186, (1994) 143–149

J. Dutta Majumdar, I. Manna, Laser surface alloying of copper with chromium Mater. Sci. Engr.

Vol A268, (1999) 215–226.

A. Bell and H. A. Davies, Solid solubility extension in Cu-V and Cu-Cr alloys produced by chill block melt-spinning Mater. Sci. Engr. Vol A226 – 228 , (1997) 1039


H. Fernee, J. Nairn, A. Atrens, Precipitation hardening of Cu-Fe-Cr alloys part I J. Mater. Sci, vol. 36 (2001) 2711 – 2719.

Copyright (c) 2017 A.O Olofinjana and, A. and K. S. Tan


Download data is not yet available.